MACKIE TH12A-MACKIE

TH12A Powered Speaker

Manufactuer: MACKIE
£258.00
out of stock code TH12A-MACKIE Delivery: 1 - 2 working days (often next day)

Seen it Cheaper?

Contact us for the best deals

100% Secure Shopping

Buy with confidence

Telephone orders & advice

Monday - Saturday 9am - 6pm

020 8208 6988

Details

"The TH12A from Mackie is a high performance PA speaker with 2 amps built in totaling 400w of power, built in EQ and versiatile cabinet shape allowing use . All this at an incredibly affordable price!"
Acoustic Performance
  • Frequency Range (-10 dB) : 57 Hz - 20 kHz
  • Frequency Response (-3 dB) : 70 Hz - 18.5 kHz
  • Horizontal Coverage Angle : 90 Degrees
  • Vertical Coverage Angle : 60 Degrees
  • Maximum SPL Long-Term : 112 dB SPL @ 1m
  • Maximum SPL Peak : 115dB SPL@1m

    Input/Output
  • Input Type : Female XLR Balanced/Unbalanced/li>
  • Input Impedance : 20k ohms bridging; 10k ohms
  • Loop-through : Male XLR Balanced/Unbalanced
  • Level Control : Rotating Knob - 0 dB at center
  • Sensitivity : +4 dBu for full output (Level control @ center) - -36dBu for full output (Level control @max)

    Transducers
  • Low frequency : 12In/381 mm with steel frame paper cone woofer
  • High Fequency : Horn-loaded 1 in/25 mm exit compression driver

    Power Amplifiers
  • Low Frequency Power Amplifier :
    - Rated Power : 150 watts, 8 ohm load, 300 watts peak
    - THD : <0.1%
    - Signal-to-Noise Ratio :> -94 dB, 20 Hz to 20 kHz, unweighted, referenced to 138 watts into 8 ohms
    - Design: BTL Class D
  • High Frequency Power Amplifier :
    - Rated Power : 50 watts, 4 ohm load 100 watts peak
    - THD : <0.1 %
    - Signal-to-Noise Ratio :> -97 dB, 20 Hz to 20 kHz, unweighted, referenced to 50 watts into 4 ohms
    - Design:Class AB

    Electronic Crossover
  • Crossover Type: 24 dB/octave
  • Crossover Frequency : 3 kHz

    Equalization :
  • Low Frequency EQ : ±15 dB @ 80 Hz, shelving
  • Mid Frequency EQ :±15 dB, bandpass, sweepable from100 Hz to 8 kHz
  • High Frequency EQ :±15 dB @ 12 kHz, shelving
  • Direct/EQ Switch :Bypasses EQ section

    Protection Features :
  • Over-excursion Protection : econd-order sub-sonic filter
  • Thermal Protection : Independent amplifier shutdown, auto reset
  • Driver Protection : Independent HF and LF compressors

    AC Power Requirements :
  • Europe : 240 VAC, 50 Hz
  • AC Connector: 3-pin IEC 250 VAC, 20 A male
  • Fuse : 230 VAC: T 3.15 AL/250 V
  • Power Consumption : 320 watts with music, loud mix - 20 watts quiescent (idle)

    Construction Features :
  • Basic Design : Asymmetrical Trapezoidal
  • Material: Polypropylene
  • Finish : Textured
  • Handles : One on each side, one on top
  • Grille : Perforated metal with weather-resistant coating Display LEDs
  • Front : Power ON
  • Rear : Power ON, OL (overload)

    Physical Dimensions and Weight :
  • Dimensions :
    - Height : 23.5 in/596 mm
    - Width : 14.5 in/367 mm
    - Depth : 12.4 in/314 mm
    - Weight : 25.5 lb/11.6 kg

    Mounting Methods :
  • Pole-mountable via the built-in socket on the bottom of the cabinet. Be sure the pole is capable of supporting the weight of the TH-12A.























  • 400W of ultra-efficient Fast Recovery™ amplification
    - LF 300W peak power (Class-D)
    - HF 100W peak power (Class A/B)
  • High-output transducers
    - 12" high-precision woofer
    - 1" compression driver
  • Mackie Active electronics provide total system optimization
  • Precision 2-way crossover
  • Transducer time-alignment
  • User-adjustable 3-band contour EQ with sweepable mid-frequency
  • Mic/Line input for direct connection of single microphone
  • Tough, impact-resistant polypropylene enclosure
  • Pole-mountable and floor wedge-able
  • Extremely lightweight and portable (25.5 lbs)

  • Write your own Review for this MACKIE TH12A-MACKIE